LED Luminescent Spectrum

LED Luminescent Spectrum

 

Spectrum is the relative distribution of wavelength and light intensity. The spectrum of LED is generally monochromatic LED, such as blue LED with a peak wavelength of 470nm, with shorter peak wavelength ultraviolet area and with longer peak wavelength green areas as the determination limitation of light intensity.

And the spectrum of incandescent lamp, its luminous intensity is widely distributed in the blue area 400nm to 700nm near infrared field, in the field of ultraviolet and infrared can also observe the luminous intensity. As for Fluorescent lamp, the part of combination usage's phosphor light wavelength is the peak of the spectrum.

Compared with the ordinary red, green and blue LED spectral peak, the white LED spectrum is different. For example, there are two luminous intensity peaks in the area of blue and yellow, or in the blue field, yellow and red fields, there are three peaks, and even more. This is because the white LED white light is a combination of multiple wavelengths of light. For instance, a combination of blue and yellow phosphor LED, the peak is in the blue and yellow field. In addition, based on the blue LED luminous intensity of peak is sharp, and the phosphor peak is relatively flat.

When the LED is used in the liquid crystal panel back light, the most ideal situation is that the spectrum of LED appears luminous intensity peaks in three areas of red, green and blue. This is because the LED light will eventually be output to the outside through the liquid crystal panel of the color filter (red, green, blue).

Getting three luminous intensity peaks, using red, green and blue three kinds of LED, and through improved phosphor material, use method of obtaining three peak of white LED

 

The lighting of blue LED and YAG phosphor, blue LED and ZnSe single crystal plate, UV LED and RGB phosphors and white LED light spectra and fluorescence light and natural light. Although they are white, but the emission spectrum is different, on the other hand, when LED is used for ordinary lighting apparatus, the white LED will be more popular where the spectrum is widely distributed in the visual field. The reason is that close to the natural light, when the spectrum of the sun's rays illuminates the object, the color of the object is close to the nature of the exposure to light

 

LED Luminescent Spectrum

LED Luminescent Spectrum

 

Spectrum is the relative distribution of wavelength and light intensity. The spectrum of LED is generally monochromatic LED, such as blue LED with a peak wavelength of 470nm, with shorter peak wavelength ultraviolet area and with longer peak wavelength green areas as the determination limitation of light intensity.

And the spectrum of incandescent lamp, its luminous intensity is widely distributed in the blue area 400nm to 700nm near infrared field, in the field of ultraviolet and infrared can also observe the luminous intensity. As for Fluorescent lamp, the part of combination usage's phosphor light wavelength is the peak of the spectrum.

Compared with the ordinary red, green and blue LED spectral peak, the white LED spectrum is different. For example, there are two luminous intensity peaks in the area of blue and yellow, or in the blue field, yellow and red fields, there are three peaks, and even more. This is because the white LED white light is a combination of multiple wavelengths of light. For instance, a combination of blue and yellow phosphor LED, the peak is in the blue and yellow field. In addition, based on the blue LED luminous intensity of peak is sharp, and the phosphor peak is relatively flat.

When the LED is used in the liquid crystal panel back light, the most ideal situation is that the spectrum of LED appears luminous intensity peaks in three areas of red, green and blue. This is because the LED light will eventually be output to the outside through the liquid crystal panel of the color filter (red, green, blue).

Getting three luminous intensity peaks, using red, green and blue three kinds of LED, and through improved phosphor material, use method of obtaining three peak of white LED

 

The lighting of blue LED and YAG phosphor, blue LED and ZnSe single crystal plate, UV LED and RGB phosphors and white LED light spectra and fluorescence light and natural light. Although they are white, but the emission spectrum is different, on the other hand, when LED is used for ordinary lighting apparatus, the white LED will be more popular where the spectrum is widely distributed in the visual field. The reason is that close to the natural light, when the spectrum of the sun's rays illuminates the object, the color of the object is close to the nature of the exposure to light

 

Integrating Sphere Development

Integrating Sphere Development

 

Integrating Sphere is used for flux measurement, which can make test result more reliable. Integrating Sphere can reduce the measurement error caused by the shape of light, divergence angle and responsiveness difference in different location on detector.

Let us learn more details about the development of Integrating Sphere manufacture technology.

Picture 1:Old Model Integrating Sphere

Picture 1 is old model Integrating Sphere. The hemisphere manufacturing technology of this Integrating Sphere is surrounded by six iron sheets via angle iron, and then two hemispheres are connected by fixture. The bottom adopts adjustable foot to support and fix the whole sphere.

Picture 2 Improved Model Integrating Sphere

Picture 2 is the improved model integrating sphere. This integrating sphere specification makes no difference with old model. But the critical technologies are that hemisphere is disposable stamping by mould. Technology requirements are very high. Measurement data error is quite small. Overall appearance is succinct.

Picture 3  Latest Integrating Sphere

The overall structure of latest Integrating Sphere is simple and beautiful with powerful function. This sphere can be assembled in half. The hemisphere width can be controlled at about 1/2 of the entire width of the sphere after disassembly, which is convenient to transport, especially for small office or laboratory door. The disassembly and installation of this model Integrating Sphere just needs to twist six screws in bracket.

 

 

In addition, Lisun is the first to achieve the integration of Integrating Sphere and Cabinet. We can put spectroradiometer, digital power meter and power source in the cabinet, which greatly facilitate the installation of wires.

 

Jacky Installation training in Poland

Jacky Installation training in Poland

 

This Polish customer purchased a High & Low Temperature and Humidity Chamber, IK level Tester and Dustproof Testing Machine from LISUN this time. They are a relatively large lighting manufacturer. We arranged engineer to do installation and training for them when confirm that the customer received the goods. The customer is very satisfied with our service, and indicating that we are the most responsible Chinese manufacturer they have met and will continue cooperating with us in the future.

 

We share some photos here:

[caption id="attachment_8795" align="alignnone" width="800"] Figure 1: Jacky (the right 2) with the client's photo[/caption]

 

[caption id="attachment_8797" align="alignnone" width="800"] Figure 2: The customer is installing the device[/caption]

[caption id="attachment_8798" align="alignnone" width="800"] Figure 3: Customer are familiar with the operation[/caption]

[caption id="attachment_8799" align="alignnone" width="800"] Figure 4: Customer is practicing the operation[/caption]

Introduction of EMC Testing

Introduction of EMC Testing

 

EMC (Electro-Magnetic Compatibility) refers to the ability of a device or system to function in its electromagnetic environment and does not constitute an unacceptable electromagnetic disturbance to anything in that environment. EMC is an important indicator of product quality.

 

EMC tests include:

 

• EMI (Electro-Magnetic Interference): Electromagnetic disturbance testing

The purpose of this test is to detect the effects of electromagnetic radiation generated by electrical products on the human body, the public grid, and other electrical appliances that are working properly.

 

(2) EMS(Electro-Magnetic Susceptibility): Electromagnetic Immunity Test

The purpose of this test is to detect electrical products whether can work stable and unaffected in the electromagnetic environment.

 

EMI tests include:

 

(1) Radiated disturbance test (RE) - Test standard: EN55022

(2) Conducted disturbance test (CE) - Test standard: EN55022

(3) Harmonic current test (Harmonic) - Test standard: EN 61000-3-2

(4) Voltage change and flicker test (Flicker) - Test standard: EN 61000-3-3

 

EMS tests include:

 

(1) Electrostatic discharge immunity test (ESD) - Test standard: EN61000-4-2

(2) Radio frequency electromagnetic field radiation immunity test (RS) - Test standard: EN61000-4-3

(3) Conducted disturbance immunity test (CS) for RF field sensing - Test standard: EN61000-4-6

(4) Electrical fast transient immunity test (EFT) - Test standard: EN61000-4-4

(5) Surge immunity test (SURGE) - Test standard: EN61000-4-5

(6) Voltage dips, short interruptions and voltage variations Immunity test (DIP) - Test standard: EN61000-4-11

(7) Power frequency magnetic field immunity test (PFMF) - Test standard: EN61000-4-8

 

 

Brief introduction of CE certificates

 

In recent years, the CE marks are more and more widely used in the market of European economic area (Member states of the European Union and the European Free Trade association, except Switzerland). More customs of different countries set out the requirements of CE certification for imported products. Exporter will be in trouble as well as unnecessary loss if their shipping goods don't have CE certified label. So, what is the importance of CE certification? What are the forms of CE certification so far? And what are the risks of products that has not been certified by CE?

 

1. The importance of CE certification

 

The CE mark on the packaging indicates that it meets the requirements of a series of European directives such as safety, sanitation, environmental protection and consumer protection. In the past, EC(European

Community)countries require differently for import and sale of products. The goods which are produced according to national standards may not be on the market. As part of the efforts to eliminate trade barriers, CE came into being at that time. Therefore, CE can be understood as CONFORMITY WITH EUROPEAN (DEMAND) (in Europe).

 

The meaning of the CE mark is as the following: Using CE acronym as symbol shows products which affix the CE mark meet the main requirements of relevant provisions of the European Directive (Essential Requirements),and it's also used to verify that the products have passed the conformity assessment procedure or the manufacturer's declaration of conformity. The CE mark is truly as a passport for the products being allowed to enter the European market. For industrial products which must affix CE mark according to relevant instructions, they can be in the market without CE mark, or they must be taken back if they don't meet safety requirements but with CE mark and in the market. For industrial products which must affix CE mark according to relevant instructions, they can be in the market without CE mark, or they must be taken back if they don't meet safety requirements but with CE mark and in the market. Moreover, the products will be restricted and prohibited from entering the EU market or forced to withdraw from the market if they violate CE mark instructions in European Directive.

 

 

The most important function of CE is to ensure the safety of the products and ensure the products work well under the conditions of the European union. CE mark like a tickets for products entering the European market, if products are not certified by CE, it's most likely to be seized of by European customs and cause exporters’ unnecessary losses.

 

2. Advantages of CE certification

The import of CE certified electronic instruments and equipment can effectively avoid the following risks:

• The risk of being detained and investigated by the customs;


• The risk of being investigated and dealt with by the market supervision institution;


• The risk of being charged by competitor for other purpose;

 

The import of CE certified electronic instruments and equipment has the following advantages:

• The import of CE certified equipment can avoid a lot of trouble in the import and export because the laws, regulations as well as standards of EU are not only numerous, but also very complex;


• It can enhance the reliability of their product performance by using CE certified equipment for testing or production. It also can effectively prevent the emergence of irresponsible allegations;


• The CE certificate of the institution designated by European Union will be the important evidence with legal effect when you are facing to litigation;

 

For electronic equipment and testing equipment, there is a very important parameter " EMC test" when the products are doing CE certification. Because the power grid frequency, voltage in Europe countries are differen from China Mainland, these products are likely to be damaged in the course of use if not detected. At the same time, there are many interference factors such as pulse group, lightning surge interference, voltage dip and so on. If there is no CE certification, the equipment is likely to be damaged and can't be used normally.

 

3. Current forms of CE certification in China mainland

At present, there are three kinds of domestic CE certification as following:

 

A：Only certified certificate, no test report:

This type of certificate is almost invalid and cannot be queried on the appropriate website. Products with this certification mark can't be recognized as ticket to the European market. Products with this kind of certificate is equivalent to the product without CE mark, and they should be detained or even returned.

B: Certificate of compliance / Certificate of compliance, with test report:

       This type of certificate is issued as a statement of conformity by the third party Agency (agency or test certification body). The test reports and other technical documents TCF should be enclosed by this kind of certificate. At the same time, enterprises also have to sign the<declaration of conformity>. This type of certification report is only recognized in mainland China. Although there are the test report and related certificates according to the requirement, the relevant information can only be checked on the detection of the company's own website. But many such testing company themself do not comply with EU certification requirements. The certificate is only applicable to the manufacturer for product quality self inspection, there is also a greater risk of being detained by the customs ana cause fines and delivery delays. This will affect the normal use of products. This kind f certificate is shown in the following figure :

[caption id="attachment_8761" align="alignnone" width="800"] Brief introduction of CE certificates[/caption]

 

 

 

 

 

C: EC Attestation of conformity < EU standard compliance certificate >

This type of certificate is issued by the EU notified body (Notified Body known as NB). According to EU regulations, only the NB are eligible to issue EC Type CE Declaration.

This type of certificate and test report are issued by testing organization certified by EU. The products finish the complete testing during the certification process and has a complete test report. Meanwhile, certificate No. can be found in the appropriate Website. Only these electronic equipment which has finished the testing and certification  can be exported to EU and can get CE label. All of Lisun series devices do CE certification in such bodies certified by European Union, and has integrated <EU standard compliance certificate> and corresponding test report. Certificate template is shown in the following figure:

[caption id="attachment_8762" align="alignnone" width="800"] Brief introduction of CE certificates[/caption]

 

 

 

 

Lisun is lead in designing and producing high quality, high precision, high performance products to Europe and customers from all over the world. Lisun applied the first CE certification at the beginning of entering the European market and provide long-term excellent quality services for European customers. When the CE certificate expires, Lisun immediately contact the top certification bodies to do

 

CE certified and testing for all products, and quickly get the CE certificates and reports that meet EU requirements. CE marks are added on all packages of the devices.

Advantages and disadvantages for total flux test of Integrating Sphere System and Goniophotometer

Advantages and disadvantages for total flux test of Integrating Sphere System and Goniophotometer

 

According to IESNA-LM-79-80, the total luminous flux (lumen) of SSL products shall be measured with an integrating sphere system or a goniophotometer. The method may be chosen depending on what other measurement quantities (color, intensity distribution) need to be measured, the size of SSL products, and other requirements.

 

The integrating sphere system is suited for total luminous flux and color measurement of integrated LED lamps and relatively small-size LED luminaires. The integrating sphere system has the advantage of fast measurement and does not require a dark room. Air movement is minimized and temperature within the sphere is not subject to the fluctuations potentially present in a temperature-controlled room. It should be noted that the heat from the SSL product mounted in or on the integrating sphere may accumulate to increase the ambient temperature of the product under test. Two types of integrating sphere systems are used, one employing a V(l)-corrected photometer head, and another employing a spectroradiometer as the detector. Spectral mismatch errors occur with the first method due to the deviation of the relative spectral responsivity of the integrating sphere photometer from the V(l), while there are theoretically no spectral mismatch errors with the second method.

 

The spectroradiometer method is preferred for measurement of SSL products because spectral mismatch errors with the photometer head tend to be significant for LED emissions and correction is not trivial, requiring knowledge of the system spectral responsivity as well as the spectrum of the device under test. In addition, with the spectroradiometer method, color quantities can be measured at the same time as total luminous flux.

 

Goniophotometers provide measurement of luminous intensity distribution as well as total luminous flux. Goniophotometers can measure total luminous flux of SSL products of relatively large size (corresponding

to dimensions of traditional fluorescent lamp luminaires) while they can measure small SSL products as well. A goniophotometer is installed in a dark room, normally temperature-controlled, and is not subject to heat accumulation from a source being measured. Care must be taken, however, for drafts from ventilation that might affect measurement of SSL products that are sensitive to temperature. Measurements with a goniophotometer are

time-consuming compared to a sphere photometer. Goniophotometers using broadband photopic detectors are susceptible to the spectral mismatch errors noted above. In fact, correction for spectral mismatch can be more difficult if there is significant variation in color with angle.

 

Generally, when integrating sphere system and Goniophotometer test light source, the difference of data is not large. If test luminaries, the test result of Goniophotometer should be as the criterion, of course, it should ensure that the calibration of Goniophotometer accurate. According to formal test requirements, integrating sphere system is to test for light source, Goniophototmeter is to test for luminaires.

 

Lisun LSG-2000 is an automatic light distribution intensity 3D curve testing system. The measuring distance is from 5m to 30m. It can measure all types of lighting sources, LED or HID luminaires such as indoor and ourdoor luminaires, roadway luminaires, street lamps, flood lights and other kinds of luminaires.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System is widely applied to Luminaries manufacturing enterprise and lab, such as Sharp Electronics in Memphis TN(USA), CS TECH MEXICO, S.A. DE C.V. (Mexico), DORADO Praha s.r.o. (Czech) etc. The reason why Lisun can win some many customers is because we always practice the motto of right products, right price and right service. Lisun will continue feedback good quality products and superior service in the feature.

What are EMC tests?

What are EMC tests?

 

With the widespread use of electrical and electronic equipment, the problem of electromagnetic disturbance has also brought electromagnetic pollution.

 

EMC(Electro Magnetic Compatibility) refers to the ability of a device or system to operate within its electromagnetic environment without incurring unacceptable electromagnetic interference to any device in its environment.



EMC testing, one the one hand refers to the electromagnetic interference from the devices during normal operation in its environment cannot exceed a certain limit, on the other hand refers to the appliance has a degree of immunity to electromagnetic interference present in the environment. It divides broadly into emissions testing and susceptibility testing.

 

Electromagnetic Interference (EMI):

1. RE (Radiated Emission): Test unintentional release of electromagnetic energy from an electronic device or apparatus.


2. CE( Conducted Emission): Test the electromagnetic energy travelling along the power line, control line or signals lines.

 

EMC tests mainly contains as following:

1. Electrostatic discharge immunity test IEC61000-4-2


2. Radiated, radio-frequency, electromagnetic field immunity test IEC61000-4-3


3. Electrical fast transient/burst immunity IEC61000-4-4


4. Surge Immunity test IEC61000-4-5


5. Immunity to conducted disturbances, induced by radio-frequency fields IEC61000-4-6


6. Power frequency magnetic field immunity test IEC61000-4-8


7. Voltage dips, short interruptions and voltage variations immunity IEC61000-4-11


8. Ring Wave immunity IEC61000-4-12


9. Damped oscillatory wave immunity test IEC61000-4-18


10. Electro Magnetic Interference test system CRSPR11~12、CRSPR14~16、CRSPR20~22

 

Lisun can provide EMC test all solutions. Please contact us if you have needs

LISUN Engineer visit our Chile customer and do installation & training here in December 2017

LISUN Engineer visit our Chile customer and do installation & training here in December 2017

 

The destination of this trip is Chile. LISUN engineer Jacky went there to do installation & training for our customer. This customer purchased a LSG-1700B Rotation Luminaire Goniophotometer (Big Size) from our company this time.



This is a LED luminaries manufacturers, they heard of LISUN from their friends and contact us directly. And finally, they purchase a set of LSG-1700B Rotation Luminaire Goniophotometer (Big Size).

 

Finally, we share some photos here:

[caption id="attachment_8708" align="alignnone" width="800"] Figure 1: LISUN engineer (The middle) and our client[/caption]

[caption id="attachment_8709" align="alignnone" width="800"] Figure 2: The LSG-1700B Rotation Luminaire Goniophotometer (Big Size) has been installed[/caption]

Goniophotometer System Standard Operating Procedures

Goniophotometer System Standard Operating Procedures

 

Goniophotometer is mainly used to measure the light performance of luminaries and light source, it mainly could measure the light intensity distribution curve, light intensity data, beam angle, total flux, luminaries efficiency, zonal luminaries flux, luminance distribution, coefficient of utilization, luminance limitation curves, maximum efficiency ratio of distance to height, equal illuminance diagram, effective average illuminance curve, spatial color distribution and average color parameters and so on.

Lisun LSG-1800B is a high performance Goniophotometer. How to do standard operation for Goniophotometer?

1. Firstly, it is preparation.


2. Before operation, testers should detect whether the connection between signals lines, control lines and power lines of Goniophotometer different parts are normal.


3. System rotation cabinet panel key switch, open the total power, and then press ”Motor” button to open the power of mechanical part, press ”Meter” button to open the power of photo tester and angle monitor, and then press LS2010 Digital Power Meter switch to open the power of Digital Power Meter.


4. Observe whether the testers in the cabinet are normal connected with mechanical parts. Under normal circumstances, except reference signals all display “0” in the testers, the rest can have data immediately; If all show “0”, it indicates that the test equipment and mechanical parts failed to connect, shut down the power of each equipment in the cabinet and open again.


5. Switch the rocker switch to “CF” on the cabinet panel.


6. Open the system power of computer, when the computer enters Windows interface, double-click LSG-1800B System software.

 

2. Install and lit luminaries


3. Choose the luminaries (or light source) under test. The chosen test luminaries (or light source) should meet the national standards which should be representative and can reflect the type performance of the luminaries (or light source) under test. For new light, it should meet the product requirement of enterprise standard; it requires aging treatment before test.


4. Install the luminaries (or light source) under test, please wear clean gloves, please wipe the luminaries (or light source) surface stains before test. When check luminaries (or light source) to test system, please note that aim the light emitting surface center (or light source center) at “+” center, and record the value of the dial angle scales in this case.


5. Clamp the clip to the two ports of the test luminaries (or light source) power supply. Please note that the two pins of the clip should plug in red and blue sockets, the two pins of another clip should plug in yellow and grebe sockets, start zero measurement. After zero measurement, the result will be saved automatically in the system files.


6. If the power of test luminaries (or light source) is not exceed 1KW, switch the rocker switch on the cabinet panel to “CF” position. Adjust the frequency conversion output power switch, until the voltage data on the digital power meter reaches the rated voltage value of luminaries(or light source), lit the test luminaries (or light source) and wait until the luminaries (or light source) light stably. General thermal radiation source needs 15 minutes, gas discharge light source needs 30 minutes.


7. If the power of test luminaries (or light source) is exceed 1KW, switch the rocker switch on the cabinet panel to “OUTER” position, power the luminaries (or light source) under test by AC Power Source or DC Power Source directly, lit the test luminaries (or light source) and wait until the luminaries (or light source) light stably. General thermal radiation source needs 15 minutes, gas discharge light source needs 30 minutes.

 

3. Measurement


4. Set the angle value of the test system at present(Horizontal angle is the value that the dial scale value of before record minus 180 degree, because this system angular coordinates is -180 degree to +180 degree, vertical angle is 0 degree).


5. Run LSG-1800B Goniophotometer test software to set a series of parameters of the luminaries under test, measure and process data.


6. If you want to save, click “Save” button, select the file format.


7. If you want to read the saved date, click “Read” button, choose the appropriate data file format and click.


8. If print, click “Print Report” button, choose appropriate print option and print automatically, make sure that the power supply of printer is open.


9. If you exit the system, click ”Exit” button to exit.


10. Shut down the power supply of luminaries (or light source) under test; remove the luminaries (or light source) under test.


11. Shut down all power supplies of the equipment in the cabinet, shut down the power supply of mechanical part and shut down the total power supply at last.

 

Lisun LSG-1800B High Precision Rotation Luminaries Goniophotometer System is widely applied to Luminaries manufacturing enterprise and lab, such as Sharp Electronics in Memphis TN(USA), CS TECH MEXICO, S.A. DE C.V. (Mexico), DORADO Praha s.r.o. (Czech) etc. The reason why Lisun can win some many customers is because we always practice the motto of right products, right price and right service. Lisun will continue feedback good quality products and superior service in the feature.

LED Plant Lighting Lamp

LED Plant Lighting Lamp

Light environment is one of the indispensable and important physical environmental factors for plant growth and development. LED plant lighting lamp is a kind of artificial light source to meet plant photosynthesis light conditions. In the absence of sunlight, lamp can act as daylight.



Plant growth lights play the function of environmental protection and energy conservation. LED plant lights provide photosynthesis light conditions, promote plant growth, short the time of plant bloom and bear fruit, improve production. It is an indispensable product for crops during modernization construction.

 

The wavelength types of LED plant lamps are rich, which is coincided with the spectral range of plant photosynthesis and photomorphogenesis. It can concentrate the light of a specific wavelength to irradiate the crop evenly. Not only it can regulate crop flowering and fruiting, but also it can control plant height and plant nutrients. System has less heat and less space, which can be used for multi-layer cultivation composite system to meet low heat load and production space miniaturized.

 

Light spectrum direct impact on plant photosynthesis is mainly red and blue. Red light is concentrated in the 630nm~660nm, its role is to help plant bloom and bear fruit; blue light is concentrated in the 450nm~470nm, its role is to help plant grow stems and leaves. 

 

Plant lighting is one of the most wide used fields of LED agriculture application, greenhouse, plant tissue culture, plant and mushroom production and many other occasions can use LED instead of traditional light source. At present, LED plant light source is mainly applied in artificial lighting in greenhouse, plants factory and plant tissue culture seedlings.

 

Many large lighting companies have developed LED plant lighting business. Utilizing LED optimize planting system to achieve sustainable crop planting throughout the year. Under the circumstances of the rapid growth in global demand for organic food, LED plant lighting applications will be more and more wide.

LISUN Engineer Stay in Turkey to do Installation & training in January 2017

LISUN Engineer Stay in Turkey to do Installation & training in January 2017

 

In January 2017, LISUN attend the Istanbul Lighting Fair. And after that LISUN engineer come to our customers’ company to do installation and training and also visit some of our old customers here.

 

This customer purchased LPCE-3 Integrating Sphere & Spectroradiometer Compact LED Test System from LISUN this time. They choose LISUN because their friend company has the instruments from LISUN and the they works very well. Many thanks for our customer’s promotion for LISUN. We would continue to presenting more and more high quality products to our customers in the future!

 

Let's share some of the photos with you below:

[caption id="attachment_8662" align="alignnone" width="800"] Figure 1: Photo of LISUN engineer (Second on the right) and our customer[/caption]

[caption id="attachment_8663" align="alignnone" width="800"] Figure 2: the customer is discussing the operation method[/caption]

[caption id="attachment_8664" align="alignnone" width="800"] Figure 3: the client is practicing the actual operation[/caption]

LISUN Engineer Stay in Turkey to do Installation & training in January 2017

LISUN Engineer Stay in Turkey to do Installation & training in January 2017

 

In January 2017, LISUN attend the Istanbul Lighting Fair. And after that LISUN engineer come to our customers’ company to do installation and training and also visit some of our old customers here.

 

This customer purchased LPCE-3 Integrating Sphere & Spectroradiometer Compact LED Test System from LISUN this time. They choose LISUN because their friend company has the instruments from LISUN and the they works very well. Many thanks for our customer’s promotion for LISUN. We would continue to presenting more and more high quality products to our customers in the future!

 

Let's share some of the photos with you below:

[caption id="attachment_8662" align="alignnone" width="800"] Figure 1: Photo of LISUN engineer (Second on the right) and our customer[/caption]

[caption id="attachment_8663" align="alignnone" width="800"] Figure 2: the customer is discussing the operation method[/caption]

[caption id="attachment_8664" align="alignnone" width="800"] Figure 3: the client is practicing the actual operation[/caption]

Installation & Training in Brazil

Installation & Training  in Brazil

 

After doing  install and traning for EVERLIGHT INDUSTRIA E COMERCIO LTDA, Lisun engineer visit local another customer Studio XXI Metalurgica Eirelli and also provide the customer with install and training, this time they purchased LSG-1700B  high precision rotating luminaire goniophotometer. The visit went off successfully, as was to have been expected. Besides, With tremendous technical strength, honest services, reasonable price and good reputation, we have got high praise from the customer. Before the ending of the visiting in company, the customer said that they would purchase LISUN instruments if they still have other need later. For this visiting in Brazil, it  is meaningful and happy for our engineer. The following is some install & training photos at customer side:

 

[caption id="attachment_8652" align="alignnone" width="600"] Figure 1: LSG-1700B high precision rotating luminaire goniophotometer[/caption]

Installation & Training in Brazil

Installation & Training in Brazil

After doing install and traning for EVERLIGHT INDUSTRIA E COMERCIO LTDA, Lisun engineer visit local another customer Studio XXI Metalurgica Eirelli and also provide the customer with install and training, this time they purchased LSG-1700B high precision rotating luminaire goniophotometer. The visit went off successfully, as was to have been expected. Besides, With tremendous technical strength, honest services, reasonable price and good reputation, we have got high praise from the customer. Before the ending of the visiting in company, the customer said that they would purchase LISUN instruments if they still have other need later. For this visiting in Brazil, it is meaningful and happy for our engineer. The following is some install & training photos at customer side:

[caption id="attachment_8652" align="alignnone" width="600"] Figure 1: LSG-1700B high precision rotating luminaire goniophotometer[/caption]

Installation & Training in Brazil

Installation & Training  in Brazil

 

After doing  install and traning for EVERLIGHT INDUSTRIA E COMERCIO LTDA, Lisun engineer visit local another customer Studio XXI Metalurgica Eirelli and also provide the customer with install and training, this time they purchased LSG-1700B  high precision rotating luminaire goniophotometer. The visit went off successfully, as was to have been expected. Besides, With tremendous technical strength, honest services, reasonable price and good reputation, we have got high praise from the customer. Before the ending of the visiting in company, the customer said that they would purchase LISUN instruments if they still have other need later. For this visiting in Brazil, it  is meaningful and happy for our engineer. The following is some install & training photos at customer side:

[caption id="attachment_8652" align="alignnone" width="600"] Figure 1: LSG-1700B high precision rotating luminaire goniophotometer[/caption]

Moving Mirror Goniophotometer Introduction

Moving Mirror Goniophotometer Introduction

Lisun LSG-2000 Moving Mirror Goniophotometer System adapts the solution of rotating mirror in the center, it is widely applied in road lamp, room lamp, spot lights, stage lights, Mining lamp, Automobile lamp, traffic signal lamp and LED lamp etc. all kinds of luminaries for light distribution performance(light distribution curve) measurement, it can also test total flux, luminaries efficiency for all types of lighting sources. It can realize CIEA-α，CIEB-β，CIEC-γ measurement solution with different software. The test result can be directly used as the input data of the international lighting design software, and comply with the requirements of CIE, IESNA and other international and domestic standards.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System can test spatial luminous intensity distribution, luminance intensity data, zonal luminance flux, luminance efficiency, coefficient of Utilization, luminance limitation curves glare, maximum ratio of distance to height, efficient luminescence angle, upper luminous flux, lower luminous flux, available average illuminance curve, Isocandela diagrams etc. photometry parameters, and voltage, current, power, power factor etc. electrical parameters.

Accuracy of angle: Class A.f1’<3% (Standard Class) or Class L.f1’<1.5%.

C angle：1) Rotating Range: 0°~360°; 2) Angle accuracy: 0.1°; 3) Angular Resolution: 0.001°.

γ angle: 1) Rotating Range: -180°～180°; 2) Angle accuracy: 0.1°; 3) Angular Resolution: 0.001°.

 

This system has 3 rotating axis. Main axis drives the reflective mirror rotate around the center point, reflect the light of the lamp to the detector. At the same time, auxiliary axis reverse rotates synchronously, always keeps the lamp bracket in the vertical position, to ensure the test lamp in normal ignite position in the measurement process, and achieve the lamp in the main axis direction measurement.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System can work with a CCD spectroradiometer with USB interface to test spatial CCT distribution and other spectral color parameters. The rotation motor is from Japan MITSUBISHI MOTORS to make the system rotate very smoothly and stably. And it uses Germanic Angle decode system to ensure the system accuracy. It adapts RS-232 standard interface, it can be connected to PC.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System is widely applied to Luminaries manufacturing enterprise and lab, such as Sharp Electronics in Memphis TN(USA), CS TECH MEXICO, S.A. DE C.V. (Mexico), DORADO Praha s.r.o. (Poland) etc. The reason why Lisun can win some many customers is because we always practice the motto of right products, right price and right service. Lisun will continue feedback good quality products and superior service in the feature.

 

IP Waterproof and Dustproof Rating Test

IP Waterproof and Dustproof Rating Test

 

Purpose of the test: to assess the ability of the material to prevent solids and liquids from entering the external shell

Detection range: electrical and electronic equipment, automotive aircraft and other parts

 

IP level (waterproof and dustproof) definition

IP waterproof and dustproof, refers to the protection level of electrical equipment, in accordance with its ability of preventing external objects intrusion, waterproof, moisture-proof and dustproof characteristics to be graded. The external objects include tools, human fingers, etc. which are not accessible to the live parts of the lamp to avoid electric shock. IP protection level is composed of two figures, the first number represents the level of dustproof ability for lamps, and the ability of preventing foreign objects intrusion; the second number represents the level of anti moisture and water for lamps. The larger the number is, the higher the degree of protection is. For example, IPXX.

 

The IP rating system provides a method for classifying products by the levels of waterproof, dustproof and anti-collision for electrical equipment and packaging. This system is approved by most European countries and was announced in IED529 (BS EN 60529: 1992) External Packing Protection level (IP code).

 

The degree of protection is mostly followed IP by two numbers, and the numbers are used to clarify the level of protection. The first figure indicates the extent of the equipment against the dust, or the extent to which people are protected from harm in a sealed environment. The second figure indicates the waterproof level of the device.

 

0 No protection

1 Can withstand solid material with length is more than 50mm. For example, hands accidentally touch; can withstand the vertical drop of water.

2 Can withstand solid material with diameter is more than 12mm, and length is no longer than 80mm. For example, fingers; can withstand a direct injection of water at a vertical angle of 15 °.

3 Can withstand solid material with diameter is more than 2.5mm. For example, tools or wires; can withstand direct jetting of water at a vertical angle of 60 °.

4 Can withstand solid material with a diameter is more than 1.0mm. For example, small wires; can withstand water spray from any direction- allowing limited access.

5 Dustproof, limited access (no harmful deposits). Can withstand low pressure water jet from any direction - allowing limited access.

6 Dust is difficult to enter, completely dustproof. Can withstand strong water column jet from any direction - allowing limited access.

7 Allowing for putting into 0.15m-1m depth water for a short time which can be up to 30 minutes.

8 Can withstand long-term soaking under pressure.

High and low temperature test

In natural environment, temperature and humidity are two indivisible natural factors. Due to different geographical locations in different regions, the temperature and humidity effects generated are also different. This test is used to confirm the products’ adaptability during storage, transportation and usage in the climate of some certain temperature and humidity. Severe levels depend on the high / low temperature, humidity and the time of exposure.

High temperature test is introduced in detail: this test is used to determine the adaptability of the products to store, transport and use under the conditions of high temperature and climate. The severity of the test depends on the temperature of the high temperature and the duration of the exposure. Reference test standards: GB/T 2423.2, IEC 60068-2-2, IEIA 364, MIL-STD-810F and so on.

Low Temperature Test: This test is used to confirm the products’ adaptability of storage, transportation and usage in the climate of the low temperature and humidity. Severe levels depend on the low temperature, humidity and the time of exposure.

Reference standards: GB/T 2423.1, IEC60068-2-1, EIA 364, MIL-STD-810F, etc..

Temperature shock test: This test is used to confirm the products’ adaptability during storage, transportation and usage in the climate of abrupt temperature change. Severe levels depend on the high/low temperature, dwell time and cycle number. Reference standard: IEC60068-2-14, GB2423.22, GJB150.5, etc..

High and low temperature test chamber is mainly aimed at the electrical, electronic products, components, and other materials’ adaptability during storage, transportation and usage in the high/low temperature.

The test equipment is mainly used for the products in accordance with national standards or user requirements, in low temperature, high temperature, conditions, the physical and other related characteristics of the environment simulation testing, testing, to determine the performance of the product, whether it is still able to meet the predetermined requirements, so as to provide product design, improvement, identification and factory inspection.

High and low temperature test box to prohibit the test items: 1) Explosive; 2) Combustible; 3)Tinder.

 

Lisun developed the GDJS/GDJW series High &Low Temperature and Humidity Chamber; they all meet the standard of IEC60068-2-1(GB/T2423.1) and IEC6008-2-2(GB/T2423.2). They can be applied in the CFL/LED lighting industry for the Aging Testing, that’s according to LM-80 standard.  Besides, they can also used in electronic products, and electronic components and many other area. Lisun Electronic (Shanghai) office is committed to the development and after-sales maintenance of lighting instrument, EMI / EMC testing system and safety testing instruments in the domestic and global market. The full range of products of Lisun are in strict accordance with the quality management and control of ISO9001:2008 requirements for R & D and production; Lisun is also the member unit of global lighting CIE association, all products are according to CIE requirements; in addition, all products of Lisun are certified by CE and get the qualification of the EU.

New Product - LMS-6000 Portable CCD Spectrometer

New Product - LMS-6000 Portable CCD Spectrometer

In order to meet the demands of the lighting market for handle spectrometer, Lisun launches LMS-6000 Portable CCD Spectrometer recently. Compare with Lisun CHROMA-2 Pocket Chroma Meter, LMS-6000 is lighter and easy to carry. Of course, the price is more competitive. LMS-6000 can be inserted SD card to store data, which is easy to use.

 

Let us introduce LMS-6000 briefly.

1. Spectral platform: telephoto asymmetrical crossed CT system.


2. Wavelength range: 380~780nm(350~950nm), FWHM: 2nm, Spectral resolution: 0.2nm


3. Sensor: CCD with 3648pix


4. Integration time: 50μs~20000ms


5. Stray light: <0.1%


6. Illuminance range: 5~200000lx


7. CCT range: 1000~100000K


8. Color coordinates accuracy: ±0.001@standard light source A 2856K


9. Zero calibration: automatically self calibration


10. Test mode: single/continuous


11. LCD screen: 5inch high definition IPS capacitive touch screen and resolution is up to 480*854


12. With 4000mAh rechargeable Li-ion battery continuous working time 20 hours


13. Structure: aluminum alloy carving


14. Size is one Iphone 6S and thickness is like diameter of 1RMB coin

 

LMS-6000 Test Report:



Lisun LMS-600 can be used for lighting field measurement directly. LMS-6000 can measure illuminance E(lx), Candle E(fc), CCT(K), Duv, chromaticity coordinates(x,y), SDCM, CRI, Irradiance Ee(W/m2), Photopic and Scotopic Vision ratio(S/P), Dominant wavelength etc. LMS-6000 can also measure Energy-saving lamps, CFL, HID lamps etc narrow spectrum light source. The application is very wide.

 

Welcome new and old customers to consult LMS-6000 Portable CCD Spectrometer

 

LISUN Engineer Continue to do Installation and Training in Turkey

LISUN Engineer Continue to do Installation and Training in Turkey

 

LISUN engineer visit several customers in Turkey this time. And the customer we discussed today purchased a LSG-1700B Rotation Luminaire Goniophotometer (Big Size) from LISUN this time.

 

LISUN engineer stay 2 days in our customer’s company for the installation and training. The customer is enthusiasm, and they expressed satisfaction with our service finally. It’s a happy trip here.

[caption id="attachment_8561" align="alignnone" width="800"] Figure 1: Group photo of the customer and LISUN engineer(The left)[/caption]

[caption id="attachment_8562" align="alignnone" width="800"] Figure 2: Group photo of the customer and LISUN engineer(The right)[/caption]

[caption id="attachment_8563" align="alignnone" width="800"] Figure 3: Customer are practicing the operation of LSG-1700B Rotation Luminaire[/caption]

[caption id="attachment_8564" align="alignnone" width="800"] Figure 4: Customer are practicing the operation of LSG-1700B Rotation Luminaire Goniophotometer[/caption]

Lisun Electronics Engineers went to Hungary to install Goniophotometer for our Hungary customer. Zengővári Lighting Ltd has been manufacturing lighting products for 20 years in Hungary. In October 2012, Zengővári Lighting Ltd purchased Lisun Rotation Luminaire Goniophotometer(LSG-1800) for lamp testing. Our Engineers spent three days in providing installation and training service to customers. The first day, Zengővári engineers carefully reviewed the drawing provided by Lisun Enigneers, then they installed the test system, and calibrated and debugged the instruments in accordance with CIE standards. The next day, Zengővári staff from technical department together with Lisun Engineers used the calibrated system to test some lamp samples, and they found the test result was very close to the rated specifications. On the last day, Lisun Engineers gave a detail introduction and training for Zengővári staff about the basic knowledge and relevant standards in lighting industry, such as CIE, LM-79, LM-80, as well as the usage, maintainace, after-sales for Lisun Goniophotometer(LSG-1800). Zengővári Lighting Ltd has become the largest lamp manufacturer in Europe; It can design and manufacture lighting products according to the different needs from customers. With high excellence test instruments, right price, and perfect after-sales service, Lisun Group finally wins this order from Zengővári Lighting Ltd. Before leaving, Lisun engineer team takes some photos in front of the famous statue In Budapest square. Lisun Group is Lead in CFL and LED Test Instruments. Our Main products are Spectrophotometer, Goniophotometer, Integrating Sphere, EMI, EMC Testing, Photometer and Colorimeter, LED and CFL tester, Electronic Ballast Tester, Electronic Components Tester, Electrical Safety Tester, Environmental Test Chamber, AC and DC Power Supply etc. With high precision test instruments, and combined with perfect after-sales training service, Lisun Group has won unanimous praise from domestic and foreign customers. Lisun Electronics Inc. Website: www.Lisungroup.com Email: SalesHK@Lisungroup.com

Lisun Electronics Engineers went to Hungary to install Goniophotometer for our Hungary customer.

 

Zengővári Lighting Ltd has been manufacturing lighting products for 20 years in Hungary. In October 2012, Zengővári Lighting Ltd purchased Lisun Rotation Luminaire Goniophotometer(LSG-1800) for lamp testing. Our Engineers spent three days in providing installation and training service to customers. The first day, Zengővári engineers carefully reviewed the drawing provided by Lisun Enigneers, then they installed the test system, and calibrated and debugged the instruments in accordance with CIE standards. The next day, Zengővári staff from technical department together with Lisun Engineers used the calibrated system to test some lamp samples, and they found the test result was very close to the rated specifications. On the last day, Lisun Engineers gave a detail introduction and training for Zengővári staff about the basic knowledge and relevant standards in lighting industry, such as CIE, LM-79, LM-80, as well as the usage, maintainace, after-sales for Lisun Goniophotometer(LSG-1800).

 

Zengővári Lighting Ltd has become the largest lamp manufacturer in Europe; It can design and manufacture lighting products according to the different needs from customers. With high excellence test instruments, right price, and perfect after-sales service, Lisun Group finally wins this order from Zengővári Lighting Ltd.

 

Before leaving, Lisun engineer team takes some photos in front of the famous statue In Budapest square. Lisun Group is Lead in CFL and LED Test Instruments. Our Main products are Spectrophotometer, Goniophotometer, Integrating Sphere, EMI, EMC Testing, Photometer and Colorimeter, LED and CFL tester, Electronic Ballast Tester, Electronic Components Tester, Electrical Safety Tester, Environmental Test Chamber, AC and DC Power Supply etc. With high precision test instruments, and combined with perfect after-sales training service, Lisun Group has won unanimous praise from domestic and foreign

 

LISUN engineer visit Turkey to do installation & training

LISUN engineer visit Turkey to do installation & training

 

In February 2017, LISUN engineer visit Turkey to do installation & training for our customers. This customer is a famous lamp manufacturer in Turkey. They purchase a LSG-1950S Goniophotometer for Automotive and Traffic Signal Lamps and a XYL-VI Photometer and Colorimeter from LISUN this time. We share some photos below:

[caption id="attachment_8540" align="alignnone" width="800"] Figure 1: The LSG-1950S Goniophotometer purchased by the customer[/caption]

[caption id="attachment_8541" align="alignnone" width="449"] Figure 2: The XYL-VI Photometer and Colorimeter purchased by the customer[/caption]

 

 

Moving Mirror Goniophotometer Introduction

Moving Mirror Goniophotometer Introduction

Lisun LSG-2000 Moving Mirror Goniophotometer System adapts the solution of rotating mirror in the center, it is widely applied in road lamp, room lamp, spot lights, stage lights, Mining lamp, Automobile lamp, traffic signal lamp and LED lamp etc. all kinds of luminaries for light distribution performance(light distribution curve) measurement, it can also test total flux, luminaries efficiency for all types of lighting sources. It can realize CIEA-α，CIEB-β，CIEC-γ measurement solution with different software. The test result can be directly used as the input data of the international lighting design software, and comply with the requirements of CIE, IESNA and other international and domestic standards.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System can test spatial luminous intensity distribution, luminance intensity data, zonal luminance flux, luminance efficiency, coefficient of Utilization, luminance limitation curves glare, maximum ratio of distance to height, efficient luminescence angle, upper luminous flux, lower luminous flux, available average illuminance curve, Isocandela diagrams etc. photometry parameters, and voltage, current, power, power factor etc. electrical parameters.

Accuracy of angle: Class A.f1’<3% (Standard Class) or Class L.f1’<1.5%.

C angle：1) Rotating Range: 0°~360°; 2) Angle accuracy: 0.1°; 3) Angular Resolution: 0.001°.

γ angle: 1) Rotating Range: -180°～180°; 2) Angle accuracy: 0.1°; 3) Angular Resolution: 0.001°.

 

This system has 3 rotating axis. Main axis drives the reflective mirror rotate around the center point, reflect the light of the lamp to the detector. At the same time, auxiliary axis reverse rotates synchronously, always keeps the lamp bracket in the vertical position, to ensure the test lamp in normal ignite position in the measurement process, and achieve the lamp in the main axis direction measurement.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System can work with a CCD spectroradiometer with USB interface to test spatial CCT distribution and other spectral color parameters. The rotation motor is from Japan MITSUBISHI MOTORS to make the system rotate very smoothly and stably. And it uses Germanic Angle decode system to ensure the system accuracy. It adapts RS-232 standard interface, it can be connected to PC.

 

Lisun LSG-2000 Moving Mirror Goniophotometer System is widely applied to Luminaries manufacturing enterprise and lab, such as Sharp Electronics in Memphis TN(USA), CS TECH MEXICO, S.A. DE C.V. (Mexico), DORADO Praha s.r.o. (Poland) etc. The reason why Lisun can win some many customers is because we always practice the motto of right products, right price and right service. Lisun will continue feedback good quality products and superior service in the feature.

 

LISUN engineers do installation & training in Turkey

LISUN engineers do installation & training in Turkey

In September 2017, LISUN Engineers do installation and training for customers in Turkey. This customer purchased a LSG-1800B High Precision Rotation Luminaire Goniophotometer and a set of LPCE-2 Integrating Sphere & Spectroradiometer Test System from LISUN. Here we share some photos below:

[caption id="attachment_8521" align="alignnone" width="800"] Figure 1: The LSG-1800B High Precision Rotation Luminaire Goniophotometer purchased by the customer[/caption]

[caption id="attachment_8522" align="alignnone" width="800"] Figure 2: Customer, LISUN engineer and the LSG-1800B High Precision Rotation Luminaire Goniophotometer[/caption]

[caption id="attachment_8523" align="alignnone" width="800"] Figure 3: Customer, LISUN engineer and the LPCE-2 Integrating Sphere & Spectroradiometer Test System[/caption]

[caption id="attachment_8524" align="alignnone" width="449"] Figure 4: Customer, LISUN engineer and the LPCE-2 Integrating Sphere & Spectroradiometer Test System[/caption]

LISUN engineer visit the United States to do installation & training in October 2017

LISUN engineer visit the United States to do installation & training in October 2017

 

At the end of October 2017, LISUN engineer Jacky once again set foot on the journey of installation & training for customers, and he arrived the Phoenix Sky Harbor International Airport Guide (PHX) on October 27. This customer purchased a LSG-1800BCCD High Precision Rotation Luminaire Goniospectroradiometer from LISUN this time.

 

About LSG-1800BCCD: LSG-1800BCCD Goniospectroradiometer is high precision automatic goniophotometric instrument for luminous intensity distribution measurements with facility for turning the light source. The LSG-1800BCCD can do the spatial CCT test when do the intensity distribution test. It is for industrial laboratory measurements the photometric data of luminaires such as LED luminaries, HID lamps, fluorescent lamps and so on. You can learn more at: http://www.lisungroup.com/product-id-383.html

 

Here we share some photos:

[caption id="attachment_8492" align="alignnone" width="800"] Figure 1: Jacky and the customer are installing the LSG-1800BCCD[/caption]

[caption id="attachment_8493" align="alignnone" width="800"] Figure 2: Jacky and the customer has finished the installation[/caption]

[caption id="attachment_8494" align="alignnone" width="800"] Figure 3: The customer is practicing the operation of LSG-1800BCCD[/caption]

IP Waterproof and Dustproof Rating Test

IP Waterproof and Dustproof Rating Test

Purpose of the test: to assess the ability of the material to prevent solids and liquids from entering the external shell
Detection range: electrical and electronic equipment, automotive aircraft and other parts

IP level (waterproof and dustproof) definition
IP waterproof and dustproof, refers to the protection level of electrical equipment, in accordance with its ability of preventing external objects intrusion, waterproof, moisture-proof and dustproof characteristics to be graded. The external objects include tools, human fingers, etc. which are not accessible to the live parts of the lamp to avoid electric shock. IP protection level is composed of two figures, the first number represents the level of dustproof ability for lamps, and the ability of preventing foreign objects intrusion; the second number represents the level of anti moisture and water for lamps. The larger the number is, the higher the degree of protection is. For example, IPXX.

The IP rating system provides a method for classifying products by the levels of waterproof, dustproof and anti-collision for electrical equipment and packaging. This system is approved by most European countries and was announced in IED529 (BS EN 60529: 1992) External Packing Protection level (IP code).

The degree of protection is mostly followed IP by two numbers, and the numbers are used to clarify the level of protection. The first figure indicates the extent of the equipment against the dust, or the extent to which people are protected from harm in a sealed environment. The second figure indicates the waterproof level of the device.

0 No protection
1 Can withstand solid material with length is more than 50mm. For example, hands accidentally touch; can withstand the vertical drop of water.
2 Can withstand solid material with diameter is more than 12mm, and length is no longer than 80mm. For example, fingers; can withstand a direct injection of water at a vertical angle of 15 °.
3 Can withstand solid material with diameter is more than 2.5mm. For example, tools or wires; can withstand direct jetting of water at a vertical angle of 60 °.
4 Can withstand solid material with a diameter is more than 1.0mm. For example, small wires; can withstand water spray from any direction- allowing limited access.
5 Dustproof, limited access (no harmful deposits). Can withstand low pressure water jet from any direction - allowing limited access.
6 Dust is difficult to enter, completely dustproof. Can withstand strong water column jet from any direction - allowing limited access.
7 Allowing for putting into 0.15m-1m depth water for a short time which can be up to 30 minutes.
8 Can withstand long-term soaking under pressure.

LISUN Engineer visit Brazil to do installation & Training In September 2017

LISUN Engineer visit Brazil to do installation & Training In September 2017

 

At the beginning of September 2017, LISUN engineer fly to Brazil immediately after the installation and training in the United States. LISUN Engineer stayed in Brazil for nearly half a month this time to do installation and training and meet several customers who are interested in LISUN products at the same time.

 

This article is for one of our customers in Brazil, the customer is a famous local lighting manufacturer, they build a new laboratory recently, and purchase some LED test equipments from LISUN. Such as LSG-1800BCCD High Precision Rotation Luminaire Goniospectroradiometer

, LPCE-3 Integrating Sphere & Spectroradiometer Compact LED Testing System, JL3456 Waterproof Test system and IK07-10 IK Level Tester.

 

LISUN engineer have designed the darkroom of the LSG-1800BCCD and operating room of JL-3456 waterproof test system for our customer. LISUN engineer spent 4 days here, the installation & training work smoothly, and LISUN service won the recognition of our customer

Finally we share some photos here:

[caption id="attachment_8467" align="alignnone" width="800"] Figure 1: LISUN engineer, our customer and LSG-1800BCCD Goniophotometer[/caption]

[caption id="attachment_8468" align="alignnone" width="800"] Figure 2: Customers are practicing the operation of the LSG-1800BCCD Goniophotometer[/caption]

[caption id="attachment_8470" align="alignnone" width="800"] Figure 3: LISUN engineer is training the LPCE-3 Integrating Sphere & Spectroradiometer Test System[/caption]

[caption id="attachment_8471" align="alignnone" width="800"] Figure 4: LISUN engineer, our customer and LPCE-3 Integrating Sphere & Spectroradiometer Test System[/caption]

[caption id="attachment_8472" align="alignnone" width="800"] Figure 5: LISUN engineer is training the JL3456 Waterproof Test System[/caption]

[caption id="attachment_8473" align="alignnone" width="800"] Figure 6: LISUN engineer is training the IK07-10 IK Level Test System[/caption]

LISUN engineer visit Kenya to do installation & training in AUGUST 2017

LISUN engineer visit Kenya to do installation & training in AUGUST 2017

 

LISUN engineer visit Kenya to do installation and training for customer here in early AUGUST 2017 The customer purchased the LPCE-2 High Precision Spectroradiometer & Integral Sphere Test System (1.5m Constant Integrating Sphere) from LISUN this time.

 

Our engineers go to do installation and training all over the world almost every month, our customers are very satisfied with our service, which also contribute to more and more customers, and more and more business volume. We will provide customers with better products and better service in the future.

 

Here share some photos you:

 

[caption id="attachment_8429" align="alignnone" width="800"] Picture 1: LISUN engineer (Right second) with the customer[/caption]

[caption id="attachment_8430" align="alignnone" width="800"] Picture 2: LISUN engineer are training for customer[/caption]

[caption id="attachment_8431" align="alignnone" width="800"] Picture 3: LISUN engineer practice the operation for customer[/caption]

Integrating Sphere Work Principle

Integrating Sphere Work Principle

If the total flux of light enter integrating sphere is Φ, irradiate on the inner wall area S3 of the integrating sphere. The light diffuse on the surface of the inner wall several times. Examine the illumination of the inner wall at any point M. Since the light entering the integrating sphere directly illuminates at S3, one part of the light diffused by each point on the S3 will irradiate on the observation M point directly, the illuminance of all these light illuminated to point M is called the direct illumination, which is denoted by E0. In addition, there are some light diffused from S3 to each point on the inner wall of the integrating sphere by multiple diffuse reflections and then reach to point M, the sum illuminance of this part light is called multiple diffuse reflection illuminance, which is denoted by E∑. Thus, the illuminance E of the observation point M is the sum of the two parts of the illuminance: E=E0+E∑         (1-1)

Direct Illuminance E0 www.LisunGroup.cn

In the S3 range, take a small element dSA at any point A, the total luminous flux on this surface is dΦ, then the illuminance EA of the position A: EA=dΦ/dSA, the inner wall of integrating sphere can be seen as ideal Reflector, so the brightness LA at A: LA=EAρ/π(where ρ is the diffuse reflection coefficient). If take a small element dSM at observation position A , the luminous flux from the element dSA  with brightness LA to the element dSM: dΦA=LAdSAcosi1dSMcosi1’/rA2.

dE0=dΦA/dSM=LAdSAcosi1cosi1’/rA2=LAdSA/4R2 

The physical quantities in the formulas are shown in the figure. The figure also can show: i1=i1’, rA=2Rcosi1(R is the radius of the inner wall of the integrating sphere). The illuminance of the light emitted from element dSA at the observation position M: dE0=dΦA/dSM=LAdSAcosi1cosi1’/rA2=LAdSA/4R2.

 

The physical quantities in the formulas are given and sorted and the direct illuminance of the entire S3 diffuse light at M is obtained as follows: E0=ρ∫S3dΦ/4πR2=ρΦ/4πR2                    (1-2)

Φ in the formula is the total luminous flux into the integrating sphere.

Multiple diffuse reflections illuminance E∑

Firstly analyze the light that the direct light from S3 at any position N on the inner wall and then diffuse again and directly reaches the observation position M. This part is called an additional illumination E1.

Since N also gets the direct illumination E0, the luminance L0 is L0=ρE0/π. Take surface element dSN at point N, An additional illuminance dE1 formed at position M from dSN: dE1=dΦ1/dSN=L0dSNcosi2dSMcosi2’/ 4R2cosi2cosi2’ dSM =L0dSN/4R2

Diffused by the entire interior of the integrating sphere, the total primary illuminance E1 formed at position M: E1=ρE0∫SdSN/4πR2=ρE0S/4πR2=ρE0(1-f)S1/4πR

S1 is the area of the inner wall of the whole sphere; f is the opening ratio (f=S2/S1, S2 is the spherical area at the opening)

Substitute S1=4πR2into the above equation：E1=ρ(1-f)E0                     (1-3)

Follow the same method, we could derive the second illuminance E2, the third illuminance E3 and so on formed at the position M from the first illumiance inside the inner wall:

E2=ρ(1-f)E1=[ρ(1-f)]2E0

E3=ρ(1-f)E2=[ρ(1-f)]3E0  www.lisungroup.cn

In this way, multiple diffuse reflections total illuminance is: E∑=E1+E2+E3+……=E0ρ(1-f)/[1-ρ(1-f)]                    (1-4)

Thus, the total illuminance E at the position M is: E=E0+E∑=E0/[1-ρ(1-f)]                        (1-5)

Feed the formula (1-2) above, then we can obtain:

E=ρΦ/4πR2[1-ρ(1-f)]                   (1-6)

We can see from the above formula, the illuminance at any position on the inner wall is proportional to the total luminous flux entering the integrating sphere. This is the basic formula for applying the luminous flux integrating sphere.

Shanghai Lisun (India) New Delhi Office Exhibition 2016 New Delhi LED Lighting Exhibition

 

Shanghai Lisun (India) New Delhi Office Exhibition 2016 New Delhi LED Lighting Exhibition

 

In October 5th-7th 2016, New Delhi LED lighting exhibition held in New Delhi, the capital of India. As one of India's largest LED lighting exhibition, New Delhi LED lighting exhibition displays different lighting solutions, including LED chips, LED lamps, LED package, intelligent building lighting design and LED test equipment, etc..

 

In order to do better serve for customers in India, Lisun group India Office jointly participate participate in this exhibition and display the latest LED test technology and test equipment to customers. Lisun group have been in India market for 9 years, and have been cooperating with too many local customer. There are many new and old customers to visit our booth during the exhibition, and we negotiate a new cooperation with our colleagues in India. Lisun group focus on the LED test instrument began in 2003, we have cooperated with many famous lighting companies and third party inspection agencies on this way, and we will continue to provide the best lighting test solutions and services for the customers.

 

Here are some of the details of the show:

[caption id="attachment_8399" align="alignnone" width="286"] Shanghai Lisun (India) New Delhi Office Exhibition 2016 New Delhi LED Lighting Exhibition[/caption]

LISUN engineer visit the first stop: Russia to do installation and training in the early August 2017

In early August 2017, LISUN engineer Fred go abroad again to installation and training, the first stop is Russia.

This customer purchased one LSG-1800X Rotation Luminaire Goniophotometer and a set of LPCE-2 High Precision Spectroradiometer & Integrating Sphere Compact Test System from LISUN this time.

 

Customer’s engineer is also very young and he can speak English fluently, the communication is very smooth. The installation & training lasted 3 days here.

 

Finally, we share some photos here:

[caption id="attachment_8384" align="alignnone" width="800"] Picture 1: LISUN engineer, customer engineer and LPCE-2 Spectroradiometer & Integrating Sphere Compact Test System[/caption]

Picture 1: LISUN engineer, customer engineer and LSG-1800X Gpniophotometer

[caption id="attachment_8385" align="alignnone" width="800"] Picture 2: LISUN engineer, customer engineer and LSG-1800X Gpniophotometer[/caption]

LISUN engineer visit Spain to do installation & training

LISUN engineer visit Spain to do installation & training

 

LISUN engineer visited customer in Spain in July 2017, and completed the installation and training tasks. This customer is a big lighting factory, they purchased a set of LMS-1900B Near Field Moving Detector Goniophotometer & IS-3.0 Integrating Sphere Test System from LISUN.

 

Usually, there are 2 hemispheres, customers should install them to one sphere. But this installation task is more complex. The volume of the ball is relatively large, and there is not simply two hemispheres here. They use two days to install the Integrating Sphere. The third day began the product training and operational exercises.

 

Finally, share some photos here:

[caption id="attachment_8376" align="alignnone" width="820"] Picture 1: LISUN engineer is guiding to install the integrating sphere[/caption]

[caption id="attachment_8377" align="alignnone" width="820"] Picture 2: LISUN engineer is guiding to install the integrating sphere[/caption]

[caption id="attachment_8378" align="alignnone" width="820"] Picture 3: Customer are doing test operation[/caption]

[caption id="attachment_8379" align="alignnone" width="449"] Picture 4: LISUN engineer (right) and customer’s engineer (left)[/caption]